As someone who is obsessed with Los Angeles's long-standing commercial studio system and the history of the audio and music that has come out of those places, getting asked to review the new Quad Tutti from Wolff Audio was a treat. This is a 19-inch single rack space unit featuring four channels of mic pres based on Sunset Sound's legendary Studio 1 console design. Sunset Sound was founded in the 1960s by Salvador “Tutti” Camarata, and the engineers there named the mic pres in the studio's custom consoles after him. The controls for Gain, Trim, and Fader nod at the console-style gain structuring of this preamp, as we'll see. I was really excited to try these new preamps out, as I was about to track a project in my studio and mix a project I tracked at another. A big part of my process is using harmonics and saturation by re-amping signals, so I wanted to see what the Quad Tutti would bring to both sides of what I do.
The tracking project was the new full-length album from Mizmor, a one-man extreme metal act. Liam “A.L.N.” Neighbors and I have been working together in a mix capacity for about a decade now, but this was the first time I would be doing the recording and engineering at my personal studio, Octopus Beak. This was the best "baptism by fire" I could think of for any mic preamp. Since everything in the project is essentially overdubbed, we were able to experiment with loads of different mics and dial things in to have a more "finished" sound. The majority of this album is in a deeper, lower set of alternate tunings – some of the songs go down to drop A – so I was curious to see what would happen to the fidelity as the preamps got pushed. It's blackened doom metal after all; we have to keep it brutal. This was where the Quad Tutti was different. It played nicely with all types of mics, and the range of sounds we were able to get out of the unit was pretty astonishing.
First up was tracking drums with all the shells through the Quad Tutti. We started with JZ V12s on both toms. I ran the toms as low gain as possible due to the high output of those mics, and the snap, body, and “boom" that we were able to capture sounded crystal clear. Usually, the JZ mics have great body but lack that extremely fast stick snap transient information that is a big part of why some engineers like fresh heads on a kit. We had fresh heads on, but it sounded like we had already added top-end EQ to the tom mics. They were tracked flat and sat right in the mix. There was an in-your-face dynamic push or "closeness" to them that reminded me of tracking drums with a large-format console, where a harmonic "invisible brushstroke" ties the audio together. We originally had the kick and snare – Neumann 47fet on kick in, Altec 175B on snare top – assigned to API 512c preamps, but we wanted to unify the drums, and I noticed a large difference when we swapped them to the Quad Tutti.
I like to use EQ and compression on the kick during recording, and having control over the Gain, Trim, and Fader output allowed me to push into the preamp like I do with a console before hitting my processing; I was able to achieve a consistency with the kick and snare by clipping the channels before adding EQ and compression. I love less audible compression when I mix, so I'm always finding ways to tame, clip, and soften transients before adding dynamics processing. This helps me get a more consistent tone and volume on individual sources, buses, and groups. In extreme metal, like Mizmor's music, songs have sections of blast beats and sections of doom and sludge. That invisible-sounding clipped feature allows the musician to perform with a more confident, inspired sound. As a drummer, you want to hear your kicks and snares at a consistent volume and crack as you track so you stay inspired by what you're hearing. The kick and snare were processed by API 550A EQs on the way in, and having extra transformers and op amps there always helps me in the mix later. Being able to tame and clip on the way in and get level and consistency from the Quad Tutti was a huge upgrade.
We abused this drive and harmonic saturation ability on everything. Bass DI and bass cab were through an A-Designs REDDI and Neumann CMV 563 with an M7 capsule, respectively. The REDDI and Tutti are a potent pairing; the bottom end of the DI was wide open. I didn't notice any shrinking of the frequency spectrum or that "folding" sound that happens when the bottom end eats up headroom.
As mentioned above, we pushed into the mic preamps (definitely not watching the LED level and clip indicators) to bring out the midrange of that CMV 563 M7 combo. If you know that mic, there's an inherent "heat" that is a part of its sound, and pushing the Tutti to accent that heat was a great addition to the DI sound we had. The frequency spectrum was pretty full from top to bottom. Stacking harmonics through the Quad Tutti achieved the sound of a bigger room – that big-console feel and width – even during playback, when the shells were still the loudest element.
Guitars were next. We tried a lot of combinations to get the guitars right on this album: Peluso brass-capsule P-414s, vintage Shure 545S, Royer R-121s, Sennheiser MD 421s, etc. We had each mic on a channel of the Quad Tutti and tried them one at a time, using the process mentioned above to capture what we thought was the right sound for Liam's cabinet (loaded with Weber Gray Wolf speakers). I wanted to see how these downtuned, Big Muff'd guitars would translate on different mics, as well as how they were going to handle the dynamics of leads with effects. Again, pushing into the mic preamps, trimming them, and using the output fader really felt like the audio was sitting tightly outside of my monitors. We settled on a blend of the P-414 and R-121. I was so impressed with how quiet the Quad Tutti was and how three-dimensional playback was with the majority of our main sounds being all Wolff Audio'd.
Liam will be tracking vocals and some clean guitars in his studio. Those will be processed later via the Quad Tutti, as he doesn't have any fancy mic preamps or compressors. Which brings us to the other interesting part of the Quad Tutti: the re-amping and mix processing side. It was like having four channels of "makes everything better" on hardware inserts in Pro Tools. Recently, I tracked a new EP for Faetooth up at Bear Creek Studio in Washington [Tape Op #157]. By chance, this was also another heavy, downtuned project. In the tracking session, I wanted to play things a bit safer on a few elements, as the majority of the studio's favored mic preamps are Neve or Neve-based. The clean vocals were tracked on their Neve sidecar with light compression from a [UA] 1176. With a line pad between my interface and the Quad Tutti, I wanted to see if I could simulate or replace some of my in the box workflow before hitting my vocal chains. As suspected, I was able to use the Gain, Trim, and Fader path to add excitement and consistency and tame all the transients that come with a vocal before hitting my compressors. Using the Quad Tutti to get the harmonics accentuated settled the vocal in the mix, and it felt like it had its own space that was different than the Neve glue that had been imparted during tracking. Tamed transients = better compression.
One part of my process is adding transformers and line amps to buses and subgroups as I’m nearing the completion of a mix. Typically, I’ll use my five API 550As and 512cs, along with a Requisite Audio Y7 preamp, set up as inserts to different groups/subs, and I’ll experiment to see what imparts dimension and excitement. Sometimes only the guitars or drums need it, sometimes the entire mix. The Quad Tutti sounded great on just about everything that went through it as a fun sprinkle of magic tone. Compared to my other outboard, it wasn't as hairy or dirty when pushed into. It felt like I was getting gain and clarity with more headroom than my other line amps and saturation boxes. Some songs got it on the kick and bass, and I used the other two channels for a heavy guitar bus. Because of that invisible clipping, the Quad Tutti is getting a lot of use. Even on a mix bus, being able to knock down that lightning-fast transient info before hitting my compression has made a big difference. That's why I think this unit is special – it has the ultimate control to shape harmonics.
For the engineers out there who are primarily mixing but want those harmonics that add depth and clarity, this box has it in spades. Flat recordings will benefit from processing through the channels of the Quad Tutti. This is important in today's digital audio world. Digital sounds great, it really does, but even just re-printing a multitrack (something I do often) through a unit like this adds enough harmonic substance to sum things up to a bigger, wider sound.