Vanguard Audio Labs: V1 gen2+LOLLI Pencil Condenser Kit mic

REVIEWED BY Matt Anderson

A slim JFET condenser microphone body, four uniquely patterned small-diaphragm capsules, one large-diaphragm lollipop-style capsule, a VSSM shock mount (worth checking out on its own), and a locking aluminum case for under $1000? We reviewed the original V1S in Tape Op #135 with glowing praise for quality mics at a fair price, and the gen2 upgrade takes the value and quality up one more notch. The first obvious gen2 change is a shift to a black mic body from the previous reddish-brown. After a lot of requests (especially from concert halls and people wanting to use them for video work), Vanguard decided the right decision was to move to a non-reflective shell. I’ve heard Derek Bargaehr (CEO of Vanguard) say it a few times over the years, and this is another example of Vanguard respecting function over fashion in their designs.

But the important gen2 changes are inside the mic body. The V1 gen2 circuit is a simple amplifier design similar to a vintage Neumann KM84, although not a clone and very much of its own design and sound signature. There are only four components in the audio path between the capsule and the XLR output – capsule coupling cap, transistor pair, transformer coupling cap, and custom-wound transformer – so any changes or tweaks there can make a massive sonic difference.

Starting with the capsule coupling cap, you’ll see a familiar trend in Vanguard’s literature about components being “cryogenically treated.” It’s one of those terms that makes the snake oil alarms go off. I asked Derek about this years ago; the cryogenic process is used to ensure that the components remain stable and perform as close as possible to their ideal specs. This isn’t about making components sound better; it’s about ensuring they’re operating consistently. To reiterate, when you have a circuit with four components in it, any small variation or drift can make a big difference. Derek didn’t believe it either until blind testing. The transistor is a monolithic dual JFET wired in parallel, which is another unique approach. Normally you would need to match the two transistors carefully, but these JFETs are cut from the same silicon wafer in the same spot and put together in a single 6-pin container. This translates into lower noise, better linearity and output, and better high-frequency response. The JFET coupling cap in gen2 is massive – it takes up a third of the circuit board. As far as Vanguard knows, they’re the only company making a charge amplifier microphone that uses metalized polypropylene as opposed to more typical tantalum or electrolytic capacitors. The circuit resistors are another major upgrade, as Vanguard moved up to a US-made audiophile-grade metal film resistor. This was a recommendation from the late cofounder of Vanguard Audio, Ken Avant. I’ve seen Derek go back and forth over component choices and know him not to go for the more expensive option just to stack a spec sheet for bragging rights. In this case, the upgrade made a very obvious improvement in the sound and noise floor.

But what of the (interchangeable) mic capsules that come with this unit? There are four 22 mm capsules (cardioid, wide cardioid, hypercardioid, and omnidirectional) and a large-diaphragm V34C gen2 LOLLI capsule. It is worth noting that the LOLLI allows cardioid and omni patterns via a switch on the head. Vanguard spent a lot of time trying to find a way to machine everything so that the LOLLI head would screw on and line up with the Vanguard logo on the body, but again they ended up making a function-over-fashion decision. In early testing of a few different iterations of metalwork, they found that people could break the neck and capsule out of alignment and possibly damage the lead wire. They ended up redesigning everything, with the neck keyholed into the main ring so it couldn’t rotate.

I’ve had five of the V1 and a LOLLI head here for a few weeks now, using them on just about everything. I’m designing an immersive microphone array system built around the V1, and they’ve really outdone themselves. With the multiple heads and the option to add more LOLLI heads down the line, the investment feels safe. They’ve worked well for the array and will live most of their lives there, but it’s nice to know they’re not one-trick ponies and that I have them around for other duties when needed. With all the different head and pattern options, it also means I can experiment with other immersive array arrangements in the future. I think this is one of the best microphone packages on the market and will hold its ground next to anything you put next to it.